LogoCentral de Ajuda do LTS Connect
LogoCentral de Ajuda do LTS Connect
Página inicial
NVR User ManualFeaturesFront Panel and Rear PanelDevice InstallationGetting StartedQuick SettingsCameraLive ViewPTZPlayback and SearchAI SearchAI ParametersAI DatabaseEvent ManagerPOSOperation and MaintenanceFile BackupNetworkStorageSystemAccountOutput and DisplayAudioUSB Device Auto Pop-up and ShutdownWeb Operation
ManualSapphire Series - LTDHNVR User Manual

Web Operation

How to connect, log in to, reset the password for, and navigate the Sapphire Series NVR web interface from a browser.

  • The interfaces in the Manual are used for introducing the operations and only for reference. The actual interface might be different dependent on the model you purchased. If there is inconsistency between the Manual and the actual product, the actual product shall govern.
  • The Manual is a general document for introducing the product, so there might be some functions described for the Device in the Manual not apply to the model you purchased.
  • Besides Web, you can use our Smart PSS to login the device. For detailed information, refer to Smart PSS user's manual.

Network Connection

  • The factory default IP of the Device is 192.168.1.108.
  • The Device supports monitoring on different browsers such as Safari, Firefox, Google to perform the functions such as multi-channel monitoring, PTZ control, and device parameters configurations.

Connect the Device to the network

Check to make sure the Device has connected to the network.

Configure IP settings

Configure the IP address, subnet mask and gateway for the PC and the Device. For details about network configuration of the Device, refer to 4.12 Network.

Verify the connection

On your PC, check the network connection of the Device by using "ping ***.***.***.***". Usually the return value of TTL is 255.

Web Login

Open the login dialog box

Open the browser, enter the IP address of the Device, and then press Enter. The Login in dialog box is displayed. See Figure 5-1.

NVR Web Login dialog box with user name, password, and protocol fields

Enter your credentials

Enter the user name and password.

  • The default administrator account is admin. The password is the one that was configured during initial settings. To security your account, it is recommended to keep the password properly and change it regularly.
  • Click the eye icon to display the password.
  • If you forget the password, click Forgot Password to reset the password. For details about resetting the password, refer to 5.3 Reset Password.

Log in

Click Login.

Reset Password

You can reset the password by the following methods when you forget the password for admin account.

  • If the password reset function is enabled, you can use mobile phone to scan the QR code on the local interface or web interface to reset the password.
  • If the password reset function is disabled, the system prompts indicating password resetting function is disabled. To reset the password, try either of the following ways:
    • Login the web with other user account to enable the password reset function.
    • Go to local interface to reset the password. For details, refer to 4.1.3 Reset Password.

Log in to the Web

Login the Web of the Device. The Login in dialog box is displayed. See Figure 5-2.

Web login dialog box for starting the password reset flow

Open the Reset Password interface

Click Forgot Password. The Reset Password interface is displayed. See Figure 5-3.

Reset Password Info step asking to agree to collect e-mail, MAC address, and device SN

Confirm the reset type

Click OK. The reset type interface is displayed. See Figure 5-4.

Reset Type step showing the QR code to scan and the security code entry box

Scan the QR code

Follow the onscreen instructions to scan the QR code and get the security code.

  • You can get the security code twice by scanning the same QR code. If you need to get the security code once again, refresh the interface.
  • Use the security code received in your email box to reset the password within 24 hours; otherwise the security code becomes invalid.
  • Wrong security code entrance up to five times will cause the security code locked for five minutes. After five minutes, you can continue to use this security code.

Enter the security code

In the Security code box, enter the security code received in your reserved email box.

Proceed to reset

Click Next. The new password resetting interface is displayed. See Figure 5-5.

Reset the password step showing User Name, Password, and Confirm Password fields

Enter the new password

In the Password box, enter the new password and enter it again in the Confirm Password box.

The new password can be set from 8 characters through 32 characters and contains at least two types from number, letter and special characters (excluding "'", """, ";", ":" and "&").

Save the new password

Click Save. The password resetting is started. After resetting is completed, a pop-up message is displayed to indicate the result and you will see the login interface is displayed. Then you can use the new password to login the web.

Web Main Menu

After you have logged in the Web, the main menu is displayed. See Figure 5-6.

For detailed operations, you can refer to 4 Local Basic Operation.

Web main menu with MANAGEMENT bar, function tiles for LIVE, PLAYBACK, AI, ALARM, POS, and OPERATION, and numbered callouts 1 through 7

Table 5-1

No.IconDescription
1Management menu iconIncludes configuration menu through which you can configure camera settings, network settings, storage settings, system settings, account settings, and view information.
2NoneDisplays system date and time.
3Account iconWhen you point to the account icon, the current user account is displayed.
4Operation iconClick the operation icon, select Logout, Reboot, or Shutdown according to your actual situation.
5QR code iconDisplays Cell Phone Client and Device SN QR Code.
- Cell Phone Client: Use your mobile phone to scan the QR code to add the device into the Cell Phone Client, and then you can start accessing the Device from your cell phone.
- Device SN: Obtain the Device SN by scanning the QR code. Go to the P2P management platform and add the Device SN into the platform. Then you can access and manage the device in the WAN. For details, refer to the P2P operation manual. You can also configure P2P function in the local configurations, refer to 4.1.4.3 P2P.
6Web main menu iconDisplays the web main menu.
7NoneIncludes eight function tiles: LIVE, PLAYBACK, AI, ALARM, POS, OPERATION, BACKUP, DISPLAY, and AUDIO. Click each tile to open the configuration interface of the tile.
- LIVE: You can perform the operations such as viewing real-time video, configuring channel layout, setting PTZ controls, and using smart talk and instant record functions if needed.
- PLAYBACK: Search for and play back the recorded video saved on the Device.
- ALARM: Search for alarm information and configure alarm event actions.
- AI: Configure and manage artificial intelligent events. It includes smart search, parameters, and database.
- POS: View POS information and configure related settings.
- OPERATION: View system information, import/export system configuration files, or update system.
- BACKUP: Search and back up the video files to the local PC or external storage device such as USB storage device.
- DISPLAY: Configure the display effect such as displaying content, image transparency, and resolution, and enable the zero-channel function.
- AUDIO: Manage audio files and configure the playing schedule. The audio file can be played in response to an alarm event if the voice prompts function is enabled.

USB Device Auto Pop-up and Shutdown

How the NVR automatically detects an inserted USB device for backup or upgrade, and how to safely shut down the device from the main menu, remote control, or rear panel.

CVI DVR User Manual

User manual for the LTS Sapphire Series CVI digital video recorders (DVR) — getting started, the grand tour, connecting basics, local configurations, web operations, and FAQ.

Índice

Network Connection
Connect the Device to the network
Configure IP settings
Verify the connection
Web Login
Open the login dialog box
Enter your credentials
Log in
Reset Password
Log in to the Web
Open the Reset Password interface
Confirm the reset type
Scan the QR code
Enter the security code
Proceed to reset
Enter the new password
Save the new password
Web Main Menu